Molt

In biology, moulting (British English), or molting (American English), also known as sloughing, shedding, or in many invertebrates, ecdysis, is the manner in which an animal routinely casts off a part of its body (often, but not always, an outer layer or covering), either at specific times of the year, or at specific points in its life cycle.

Moulting can involve shedding the epidermis (skin), pelage (hair, feathers, fur, wool), or other external layer. In some groups, other body parts may be shed, for example, the entire exoskeleton in arthropods, including the wings in some insects.

In birds, moulting is the periodic replacement of feathers by shedding old feathers while producing new ones. Feathers are dead structures at maturity which are gradually abraded and need to be replaced. Adult birds moult at least once a year, although many moult twice and a few three times each year.[2] It is generally a slow process as birds rarely shed all their feathers at any one time; the bird must retain sufficient feathers to regulate its body temperature and repel moisture. The number and area of feathers that are shed varies. In some moulting periods, a bird may renew only the feathers on the head and body, shedding the wing and tail feathers during a later moulting period.[2] Some species of bird become flightless during an annual "wing moult" and must seek a protected habitat with a reliable food supply during that time. While the plumage may appear thin or uneven during the moult, the bird's general shape is maintained despite the loss of apparently many feathers; bald spots are typically signs of unrelated illnesses, such as gross injuries, parasites, feather pecking (especially in commercial poultry), or (in pet birds) feather plucking. Some birds will drop feathers, especially tail feathers, in what is called a "fright moult".[3]

The process of moulting in birds is as follows: First, the bird begins to shed some old feathers, then pin feathers grow in to replace the old feathers. As the pin feathers become full feathers, other feathers are shed. This is a cyclical process that occurs in many phases. It is usually symmetrical, with feather loss equal on each side of the body.[2] Because feathers make up 4–12% of a bird's body weight, it takes a large amount of energy to replace them. For this reason, moults often occur immediately after the breeding season, but while food is still abundant. The plumage produced during this time is called postnuptial plumage.[2] Prenuptial moulting occurs in red-collared widowbirds where the males replace their nonbreeding plumage with breeding plumage. It is thought that large birds can advance the moult of severely damaged feathers.[4]

Determining the process birds go through during moult can be useful in understanding breeding, migration and foraging strategies.[5] One non-invasive method of studying moult in birds is through using field photography.[6] The evolutionary and ecological forces driving moult can also be investigated using intrinsic markers such as stable hydrogen isotope (δ2H) analysis.[7] In some tropical birds, such as the common bulbul, breeding seasonality is weak at the population level, instead moult can show high seasonality with individuals probably under strong selection to match moult with peak environmental conditions.[8]

In some countries, flocks of commercial layer hens are force-moulted to reinvigorate egg-laying. This usually involves complete withdrawal of their food and sometimes water for 7–14 days or up to 28 days under experimental conditions,[9] which presumably reflect standard farming practice in some countries. This causes a body weight loss of 25 to 35%,[10] which stimulates the hen to lose her feathers, but also reinvigorates egg-production. Some flocks may be force-moulted several times. In 2003, more than 75% of all flocks were force-moulted in the US.[11] Other methods of inducing a moult include low-density diets (e.g. grape pomace, cotton seed meal, alfalfa meal)[12] or dietary manipulation to create an imbalance of a particular nutrient(s). The most important among these include manipulation of minerals including sodium (Na), calcium (Ca), iodine (I) and zinc (Zn), with full or partially reduced dietary intakes.[13]

The most familiar example of moulting in reptiles is when snakes "shed their skin". This is usually achieved by the snake rubbing its head against a hard object, such as a rock (or between two rocks) or piece of wood, causing the already stretched skin to split. At this point, the snake continues to rub its skin on objects, causing the end nearest the head to peel back on itself, until the snake is able to crawl out of its skin, effectively turning the moulted skin inside-out. This is similar to how one might remove a sock from one's foot by grabbing the open end and pulling it over itself. The snake's skin is often left in one piece after the moulting process, including the discarded brille (ocular scale), so that the moult is vital for maintaining the animal's quality of vision. The skins of lizards, in contrast, generally fall off in pieces.

In arthropods, such as insects, arachnids and crustaceans, moulting is the shedding of the exoskeleton (which is often called its shell), typically to let the organism grow. This process is called ecdysis. It is commonly said that ecdysis is necessary because the exoskeleton is rigid and cannot grow like skin, but this is simplistic, ignoring the fact that most Arthropoda with soft, flexible skins also undergo ecdysis. Among other things, ecdysis permits metamorphosis, the sometimes radical difference between the morphology of successive instars, and the fact that a new skin can replace structures, such as by providing new external lenses for eyes. The new exoskeleton is initially soft but hardens after the moulting of the old exoskeleton. The old exoskeleton is called an exuviae. While moulting, insects can't breathe.[14]

Most dogs moult twice each year, in the spring and autumn, depending on the breed, environment and temperature. Dogs shedding much more than usual are known as "blow coats" or "blowing coats".[15][16]

Both frogs and salamanders moult regularly and consume the skin, with some species moulting in pieces and others in one piece.[17]

A moulting yellow-eyed penguin

A leopard frog moulting and eating the skin

Giant prickly stick insect crawling out of his moulted skin

Moulted snake skin

Moulting European green lizard

Discarded moult of a grasshopper (Caelifera)

A cicada moulting

Moult of a Tiliqua rugosa lizard, 5 cm scale bar

US,Alabama,Autauga,Autaugaville Postcode

post code city state latitude longitude
59057 Molt MT 45.86134 -108.92793